Commit 54dbe75b authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm

Pull drm updates from Dave Airlie:
 "This is the main drm pull request for 4.19.

  Rob has some new hardware support for new qualcomm hw that I'll send
  along separately. This has the display part of it, the remaining pull
  is for the acceleration engine.

  This also contains a wound-wait/wait-die mutex rework, Peter has acked
  it for merging via my tree.

  Otherwise mostly the usual level of activity. Summary:

  core:
   - Wound-wait/wait-die mutex rework
   - Add writeback connector type
   - Add "content type" property for HDMI
   - Move GEM bo to drm_framebuffer
   - Initial gpu scheduler documentation
   - GPU scheduler fixes for dying processes
   - Console deferred fbcon takeover support
   - Displayport support for CEC tunneling over AUX

  panel:
   - otm8009a panel driver fixes
   - Innolux TV123WAM and G070Y2-L01 panel driver
   - Ilitek ILI9881c panel driver
   - Rocktech RK070ER9427 LCD
   - EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
   - DLC DLC0700YZG-1
   - BOE HV070WSA-100
   - newhaven, nhd-4.3-480272ef-atxl LCD
   - DataImage SCF0700C48GGU18
   - Sharp LQ035Q7DB03
   - p079zca: Refactor to support multiple panels

  tinydrm:
   - ILI9341 display panel

  New driver:
   - vkms - virtual kms driver to testing.

  i915:
   - Icelake:
        Display enablement
        DSI support
        IRQ support
        Powerwell support
   - GPU reset fixes and improvements
   - Full ppgtt support refactoring
   - PSR fixes and improvements
   - Execlist improvments
   - GuC related fixes

  amdgpu:
   - Initial amdgpu documentation
   - JPEG engine support on VCN
   - CIK uses powerplay by default
   - Move to using core PCIE functionality for gens/lanes
   - DC/Powerplay interface rework
   - Stutter mode support for RV
   - Vega12 Powerplay updates
   - GFXOFF fixes
   - GPUVM fault debugging
   - Vega12 GFXOFF
   - DC improvements
   - DC i2c/aux changes
   - UVD 7.2 fixes
   - Powerplay fixes for Polaris12, CZ/ST
   - command submission bo_list fixes

  amdkfd:
   - Raven support
   - Power management fixes

  udl:
   - Cleanups and fixes

  nouveau:
   - misc fixes and cleanups.

  msm:
   - DPU1 support display controller in sdm845
   - GPU coredump support.

  vmwgfx:
   - Atomic modesetting validation fixes
   - Support for multisample surfaces

  armada:
   - Atomic modesetting support completed.

  exynos:
   - IPPv2 fixes
   - Move g2d to component framework
   - Suspend/resume support cleanups
   - Driver cleanups

  imx:
   - CSI configuration improvements
   - Driver cleanups
   - Use atomic suspend/resume helpers
   - ipu-v3 V4L2 XRGB32/XBGR32 support

  pl111:
   - Add Nomadik LCDC variant

  v3d:
   - GPU scheduler jobs management

  sun4i:
   - R40 display engine support
   - TCON TOP driver

  mediatek:
   - MT2712 SoC support

  rockchip:
   - vop fixes

  omapdrm:
   - Workaround for DRA7 errata i932
   - Fix mm_list locking

  mali-dp:
   - Writeback implementation
        PM improvements
   - Internal error reporting debugfs

  tilcdc:
   - Single fix for deferred probing

  hdlcd:
   - Teardown fixes

  tda998x:
   - Converted to a bridge driver.

  etnaviv:
   - Misc fixes"

* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
  drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
  drm/scheduler: fix param documentation
  drm/i2c: tda998x: correct PLL divider calculation
  drm/i2c: tda998x: get rid of private fill_modes function
  drm/i2c: tda998x: move mode_valid() to bridge
  drm/i2c: tda998x: register bridge outside of component helper
  drm/i2c: tda998x: cleanup from previous changes
  drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
  drm/i2c: tda998x: convert to bridge driver
  drm/scheduler: fix timeout worker setup for out of order job completions
  drm/amd/display: display connected to dp-1 does not light up
  drm/amd/display: update clk for various HDMI color depths
  drm/amd/display: program display clock on cache match
  drm/amd/display: Add NULL check for enabling dp ss
  drm/amd/display: add vbios table check for enabling dp ss
  drm/amd/display: Don't share clk source between DP and HDMI
  drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
  drm/amd/display: Use calculated disp_clk_khz value for dce110
  drm/amd/display: Implement custom degamma lut on dcn
  drm/amd/display: Destroy aux_engines only once
  ...
parents dafa5f65 557ce950

Too many changes to show.

To preserve performance only 1000 of 1000+ files are displayed.

......@@ -74,6 +74,12 @@ Required properties for DSI:
The 3 clocks output from the DSI analog PHY: dsi[01]_byte,
dsi[01]_ddr2, and dsi[01]_ddr
Required properties for the TXP (writeback) block:
- compatible: Should be "brcm,bcm2835-txp"
- reg: Physical base address and length of the TXP block's registers
- interrupts: The interrupt number
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
[1] Documentation/devicetree/bindings/media/video-interfaces.txt
Example:
......
Ilitek ILI9341 display panels
This binding is for display panels using an Ilitek ILI9341 controller in SPI
mode.
Required properties:
- compatible: "adafruit,yx240qv29", "ilitek,ili9341"
- dc-gpios: D/C pin
- reset-gpios: Reset pin
The node for this driver must be a child node of a SPI controller, hence
all mandatory properties described in ../spi/spi-bus.txt must be specified.
Optional properties:
- rotation: panel rotation in degrees counter clockwise (0,90,180,270)
- backlight: phandle of the backlight device attached to the panel
Example:
display@0{
compatible = "adafruit,yx240qv29", "ilitek,ili9341";
reg = <0>;
spi-max-frequency = <32000000>;
dc-gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
rotation = <270>;
backlight = <&backlight>;
};
......@@ -40,7 +40,7 @@ Required properties (all function blocks):
"mediatek,<chip>-dpi" - DPI controller, see mediatek,dpi.txt
"mediatek,<chip>-disp-mutex" - display mutex
"mediatek,<chip>-disp-od" - overdrive
the supported chips are mt2701 and mt8173.
the supported chips are mt2701, mt2712 and mt8173.
- reg: Physical base address and length of the function block register space
- interrupts: The interrupt signal from the function block (required, except for
merge and split function blocks).
......
Qualcomm Technologies, Inc. DPU KMS
Description:
Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates
sub-blocks like DPU display controller, DSI and DP interfaces etc.
The DPU display controller is found in SDM845 SoC.
MDSS:
Required properties:
- compatible: "qcom,sdm845-mdss"
- reg: physical base address and length of contoller's registers.
- reg-names: register region names. The following region is required:
* "mdss"
- power-domains: a power domain consumer specifier according to
Documentation/devicetree/bindings/power/power_domain.txt
- clocks: list of clock specifiers for clocks needed by the device.
- clock-names: device clock names, must be in same order as clocks property.
The following clocks are required:
* "iface"
* "bus"
* "core"
- interrupts: interrupt signal from MDSS.
- interrupt-controller: identifies the node as an interrupt controller.
- #interrupt-cells: specifies the number of cells needed to encode an interrupt
source, should be 1.
- iommus: phandle of iommu device node.
- #address-cells: number of address cells for the MDSS children. Should be 1.
- #size-cells: Should be 1.
- ranges: parent bus address space is the same as the child bus address space.
Optional properties:
- assigned-clocks: list of clock specifiers for clocks needing rate assignment
- assigned-clock-rates: list of clock frequencies sorted in the same order as
the assigned-clocks property.
MDP:
Required properties:
- compatible: "qcom,sdm845-dpu"
- reg: physical base address and length of controller's registers.
- reg-names : register region names. The following region is required:
* "mdp"
* "vbif"
- clocks: list of clock specifiers for clocks needed by the device.
- clock-names: device clock names, must be in same order as clocks property.
The following clocks are required.
* "bus"
* "iface"
* "core"
* "vsync"
- interrupts: interrupt line from DPU to MDSS.
- ports: contains the list of output ports from DPU device. These ports connect
to interfaces that are external to the DPU hardware, such as DSI, DP etc.
Each output port contains an endpoint that describes how it is connected to an
external interface. These are described by the standard properties documented
here:
Documentation/devicetree/bindings/graph.txt
Documentation/devicetree/bindings/media/video-interfaces.txt
Port 0 -> DPU_INTF1 (DSI1)
Port 1 -> DPU_INTF2 (DSI2)
Optional properties:
- assigned-clocks: list of clock specifiers for clocks needing rate assignment
- assigned-clock-rates: list of clock frequencies sorted in the same order as
the assigned-clocks property.
Example:
mdss: mdss@ae00000 {
compatible = "qcom,sdm845-mdss";
reg = <0xae00000 0x1000>;
reg-names = "mdss";
power-domains = <&clock_dispcc 0>;
clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>,
<&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
clock-names = "iface", "bus", "core";
assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>;
assigned-clock-rates = <300000000>;
interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
interrupt-controller;
#interrupt-cells = <1>;
iommus = <&apps_iommu 0>;
#address-cells = <2>;
#size-cells = <1>;
ranges = <0 0 0xae00000 0xb2008>;
mdss_mdp: mdp@ae01000 {
compatible = "qcom,sdm845-dpu";
reg = <0 0x1000 0x8f000>, <0 0xb0000 0x2008>;
reg-names = "mdp", "vbif";
clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>,
<&clock_dispcc DISP_CC_MDSS_AXI_CLK>,
<&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
<&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
clock-names = "iface", "bus", "core", "vsync";
assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>,
<&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>;
assigned-clock-rates = <0 0 300000000 19200000>;
interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
dpu_intf1_out: endpoint {
remote-endpoint = <&dsi0_in>;
};
};
port@1 {
reg = <1>;
dpu_intf2_out: endpoint {
remote-endpoint = <&dsi1_in>;
};
};
};
};
};
......@@ -119,6 +119,20 @@ Required properties:
Optional properties:
- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY
regulator is wanted.
- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode
panels in microseconds. Driver uses this number to adjust
the clock rate according to the expected transfer time.
Increasing this value would slow down the mdp processing
and can result in slower performance.
Decreasing this value can speed up the mdp processing,
but this can also impact power consumption.
As a rule this time should not be higher than the time
that would be expected with the processing at the
dsi link rate since anyways this would be the maximum
transfer time that could be achieved.
If ping pong split is enabled, this time should not be higher
than two times the dsi link rate time.
If the property is not specified, then the default value is 14000 us.
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
[2] Documentation/devicetree/bindings/graph.txt
......@@ -169,6 +183,8 @@ Example:
qcom,master-dsi;
qcom,sync-dual-dsi;
qcom,mdss-mdp-transfer-time-us = <12000>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&dsi_active>;
pinctrl-1 = <&dsi_suspend>;
......
AU Optronics Corporation 7.0" FHD (800 x 480) TFT LCD panel
Required properties:
- compatible: should be "auo,g070vvn01"
- backlight: phandle of the backlight device attached to the panel
- power-supply: single regulator to provide the supply voltage
Required nodes:
- port: Parallel port mapping to connect this display
This panel needs single power supply voltage. Its backlight is conntrolled
via PWM signal.
Example:
--------
Example device-tree definition when connected to iMX6Q based board
lcd_panel: lcd-panel {