Commit 3b3b6b46 authored by Linus Walleij's avatar Linus Walleij Committed by David S. Miller
Browse files

net: dsa: Add bindings for Realtek SMI DSAs



The Realtek SMI family is a set of DSA chips that provide
switching in routers. This binding just follows the pattern
set by other switches but with the introduction of an embedded
irqchip to demux and handle the interrupts fired by the single
line from the chip.

This interrupt construction is similar to how we handle
interrupt controllers inside PCI bridges etc.

Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent d8545825
Realtek SMI-based Switches
==========================
The SMI "Simple Management Interface" is a two-wire protocol using
bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
not use the MDIO protocol. This binding defines how to specify the
SMI-based Realtek devices.
Required properties:
- compatible: must be exactly one of:
"realtek,rtl8366"
"realtek,rtl8366rb" (4+1 ports)
"realtek,rtl8366s" (4+1 ports)
"realtek,rtl8367"
"realtek,rtl8367b"
"realtek,rtl8368s" (8 port)
"realtek,rtl8369"
"realtek,rtl8370" (8 port)
Required properties:
- mdc-gpios: GPIO line for the MDC clock line.
- mdio-gpios: GPIO line for the MDIO data line.
- reset-gpios: GPIO line for the reset signal.
Optional properties:
- realtek,disable-leds: if the LED drivers are not used in the
hardware design this will disable them so they are not turned on
and wasting power.
Required subnodes:
- interrupt-controller
This defines an interrupt controller with an IRQ line (typically
a GPIO) that will demultiplex and handle the interrupt from the single
interrupt line coming out of one of the SMI-based chips. It most
importantly provides link up/down interrupts to the PHY blocks inside
the ASIC.
Required properties of interrupt-controller:
- interrupt: parent interrupt, see interrupt-controller/interrupts.txt
- interrupt-controller: see interrupt-controller/interrupts.txt
- #address-cells: should be <0>
- #interrupt-cells: should be <1>
- mdio
This defines the internal MDIO bus of the SMI device, mostly for the
purpose of being able to hook the interrupts to the right PHY and
the right PHY to the corresponding port.
Required properties of mdio:
- compatible: should be set to "realtek,smi-mdio" for all SMI devices
See net/mdio.txt for additional MDIO bus properties.
See net/dsa/dsa.txt for a list of additional required and optional properties
and subnodes of DSA switches.
Examples:
switch {
compatible = "realtek,rtl8366rb";
/* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
switch_intc: interrupt-controller {
/* GPIO 15 provides the interrupt */
interrupt-parent = <&gpio0>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <1>;
};
ports {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
port@0 {
reg = <0>;
label = "lan0";
phy-handle = <&phy0>;
};
port@1 {
reg = <1>;
label = "lan1";
phy-handle = <&phy1>;
};
port@2 {
reg = <2>;
label = "lan2";
phy-handle = <&phy2>;
};
port@3 {
reg = <3>;
label = "lan3";
phy-handle = <&phy3>;
};
port@4 {
reg = <4>;
label = "wan";
phy-handle = <&phy4>;
};
port@5 {
reg = <5>;
label = "cpu";
ethernet = <&gmac0>;
phy-mode = "rgmii";
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
mdio {
compatible = "realtek,smi-mdio", "dsa-mdio";
#address-cells = <1>;
#size-cells = <0>;
phy0: phy@0 {
reg = <0>;
interrupt-parent = <&switch_intc>;
interrupts = <0>;
};
phy1: phy@1 {
reg = <1>;
interrupt-parent = <&switch_intc>;
interrupts = <1>;
};
phy2: phy@2 {
reg = <2>;
interrupt-parent = <&switch_intc>;
interrupts = <2>;
};
phy3: phy@3 {
reg = <3>;
interrupt-parent = <&switch_intc>;
interrupts = <3>;
};
phy4: phy@4 {
reg = <4>;
interrupt-parent = <&switch_intc>;
interrupts = <12>;
};
};
};
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment