Commit 580416e6 authored by Jeff Kirsher's avatar Jeff Kirsher
Browse files

enc28j60: Move the Microchip driver



Move the Microchip driver into drivers/net/ethernet/microchip/ and
make the necessary Kconfig and Makefile changes.

CC: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 1fe003fd
......@@ -274,23 +274,6 @@ config DM9000_FORCE_SIMPLE_PHY_POLL
costly MII PHY reads. Note, this will not work if the chip is
operating with an external PHY.
config ENC28J60
tristate "ENC28J60 support"
depends on EXPERIMENTAL && SPI && NET_ETHERNET
select CRC32
---help---
Support for the Microchip EN28J60 ethernet chip.
To compile this driver as a module, choose M here. The module will be
called enc28j60.
config ENC28J60_WRITEVERIFY
bool "Enable write verify"
depends on ENC28J60
---help---
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
depends on ISA || EISA || PCI
......
......@@ -53,7 +53,6 @@ obj-$(CONFIG_TUN) += tun.o
obj-$(CONFIG_VETH) += veth.o
obj-$(CONFIG_NET_NETX) += netx-eth.o
obj-$(CONFIG_DM9000) += dm9000.o
obj-$(CONFIG_ENC28J60) += enc28j60.o
obj-$(CONFIG_DEV_APPLETALK) += appletalk/
obj-$(CONFIG_ETHERNET) += ethernet/
......
......@@ -78,6 +78,7 @@ config LANTIQ_ETOP
source "drivers/net/ethernet/marvell/Kconfig"
source "drivers/net/ethernet/mellanox/Kconfig"
source "drivers/net/ethernet/micrel/Kconfig"
source "drivers/net/ethernet/microchip/Kconfig"
config MIPS_SIM_NET
tristate "MIPS simulator Network device"
......
......@@ -36,6 +36,7 @@ obj-$(CONFIG_LANTIQ_ETOP) += lantiq_etop.o
obj-$(CONFIG_NET_VENDOR_MARVELL) += marvell/
obj-$(CONFIG_NET_VENDOR_MELLANOX) += mellanox/
obj-$(CONFIG_NET_VENDOR_MICREL) += micrel/
obj-$(CONFIG_NET_VENDOR_MICROCHIP) += microchip/
obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
obj-$(CONFIG_NET_VENDOR_MYRI) += myricom/
obj-$(CONFIG_FEALNX) += fealnx.o
......
#
# Microchip network device configuration
#
config NET_VENDOR_MICROCHIP
bool "Microchip devices"
depends on SPI && EXPERIMENTAL
---help---
If you have a network (Ethernet) card belonging to this class, say Y
and read the Ethernet-HOWTO, available from
<http://www.tldp.org/docs.html#howto>.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about Microchip cards. If you say Y, you will be asked
for your specific card in the following questions.
if NET_VENDOR_MICROCHIP
config ENC28J60
tristate "ENC28J60 support"
depends on SPI && EXPERIMENTAL
select CRC32
---help---
Support for the Microchip EN28J60 ethernet chip.
To compile this driver as a module, choose M here. The module will be
called enc28j60.
config ENC28J60_WRITEVERIFY
bool "Enable write verify"
depends on ENC28J60
---help---
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
endif # NET_VENDOR_MICROCHIP
#
# Makefile for the Microchip network device drivers.
#
obj-$(CONFIG_ENC28J60) += enc28j60.o
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment