Commit d7058a79 authored by Jeff Kirsher's avatar Jeff Kirsher
Browse files

dm9000: Move the Davicom driver



Move the Davicom driver into drivers/net/ethernet/davicom/ and
make the necessary Kconfig and Makefile changes.

CC: Ben Dooks <ben@simtec.co.uk>
CC: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: default avatarSascha Hauer <s.hauer@pengutronix.de>
parent 580416e6
......@@ -246,34 +246,6 @@ config NET_NETX
To compile this driver as a module, choose M here. The module
will be called netx-eth.
config DM9000
tristate "DM9000 support"
depends on ARM || BLACKFIN || MIPS
select CRC32
select MII
---help---
Support for DM9000 chipset.
To compile this driver as a module, choose M here. The module
will be called dm9000.
config DM9000_DEBUGLEVEL
int "DM9000 maximum debug level"
depends on DM9000
default 4
help
The maximum level of debugging code compiled into the DM9000
driver.
config DM9000_FORCE_SIMPLE_PHY_POLL
bool "Force simple NSR based PHY polling"
depends on DM9000
---help---
This configuration forces the DM9000 to use the NSR's LinkStatus
bit to determine if the link is up or down instead of the more
costly MII PHY reads. Note, this will not work if the chip is
operating with an external PHY.
config NET_PCI
bool "EISA, VLB, PCI and on board controllers"
depends on ISA || EISA || PCI
......
......@@ -52,7 +52,6 @@ obj-$(CONFIG_EQUALIZER) += eql.o
obj-$(CONFIG_TUN) += tun.o
obj-$(CONFIG_VETH) += veth.o
obj-$(CONFIG_NET_NETX) += netx-eth.o
obj-$(CONFIG_DM9000) += dm9000.o
obj-$(CONFIG_DEV_APPLETALK) += appletalk/
obj-$(CONFIG_ETHERNET) += ethernet/
......
......@@ -24,6 +24,7 @@ source "drivers/net/ethernet/brocade/Kconfig"
source "drivers/net/ethernet/chelsio/Kconfig"
source "drivers/net/ethernet/cirrus/Kconfig"
source "drivers/net/ethernet/cisco/Kconfig"
source "drivers/net/ethernet/davicom/Kconfig"
config DNET
tristate "Dave ethernet support (DNET)"
......
......@@ -16,6 +16,7 @@ obj-$(CONFIG_NET_VENDOR_BROCADE) += brocade/
obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
obj-$(CONFIG_NET_VENDOR_CIRRUS) += cirrus/
obj-$(CONFIG_NET_VENDOR_CISCO) += cisco/
obj-$(CONFIG_DM9000) += davicom/
obj-$(CONFIG_DNET) += dnet.o
obj-$(CONFIG_NET_VENDOR_DEC) += dec/
obj-$(CONFIG_NET_VENDOR_DLINK) += dlink/
......
#
# Davicom device configuration
#
config DM9000
tristate "DM9000 support"
depends on ARM || BLACKFIN || MIPS
select CRC32
select MII
---help---
Support for DM9000 chipset.
To compile this driver as a module, choose M here. The module
will be called dm9000.
config DM9000_DEBUGLEVEL
int "DM9000 maximum debug level"
depends on DM9000
default 4
---help---
The maximum level of debugging code compiled into the DM9000
driver.
config DM9000_FORCE_SIMPLE_PHY_POLL
bool "Force simple NSR based PHY polling"
depends on DM9000
---help---
This configuration forces the DM9000 to use the NSR's LinkStatus
bit to determine if the link is up or down instead of the more
costly MII PHY reads. Note, this will not work if the chip is
operating with an external PHY.
#
# Makefile for the Davicom device drivers.
#
obj-$(CONFIG_DM9000) += dm9000.o
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment