Commit 685e444b authored by Chunyan Zhang's avatar Chunyan Zhang Committed by Ulf Hansson
Browse files

mmc: sdhci: Add ADMA2 64-bit addressing support for V4 mode



ADMA2 64-bit addressing support is divided into V3 mode and V4 mode.
So there are two kinds of descriptors for ADMA2 64-bit addressing
i.e. 96-bit Descriptor for V3 mode, and 128-bit Descriptor for V4
mode. 128-bit Descriptor is aligned to 8-byte.

For V4 mode, ADMA2 64-bit addressing is enabled via Host Control 2
register.

Signed-off-by: default avatarChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: default avatarAdrian Hunter <adrian.hunter@intel.com>
[Ulf: Fixed conflict while applying]
Signed-off-by: default avatarUlf Hansson <ulf.hansson@linaro.org>
parent 917a0c52
......@@ -266,6 +266,52 @@ static void sdhci_set_default_irqs(struct sdhci_host *host)
sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
}
static void sdhci_config_dma(struct sdhci_host *host)
{
u8 ctrl;
u16 ctrl2;
if (host->version < SDHCI_SPEC_200)
return;
ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
/*
* Always adjust the DMA selection as some controllers
* (e.g. JMicron) can't do PIO properly when the selection
* is ADMA.
*/
ctrl &= ~SDHCI_CTRL_DMA_MASK;
if (!(host->flags & SDHCI_REQ_USE_DMA))
goto out;
/* Note if DMA Select is zero then SDMA is selected */
if (host->flags & SDHCI_USE_ADMA)
ctrl |= SDHCI_CTRL_ADMA32;
if (host->flags & SDHCI_USE_64_BIT_DMA) {
/*
* If v4 mode, all supported DMA can be 64-bit addressing if
* controller supports 64-bit system address, otherwise only
* ADMA can support 64-bit addressing.
*/
if (host->v4_mode) {
ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
ctrl2 |= SDHCI_CTRL_64BIT_ADDR;
sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
} else if (host->flags & SDHCI_USE_ADMA) {
/*
* Don't need to undo SDHCI_CTRL_ADMA32 in order to
* set SDHCI_CTRL_ADMA64.
*/
ctrl |= SDHCI_CTRL_ADMA64;
}
}
out:
sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
}
static void sdhci_init(struct sdhci_host *host, int soft)
{
struct mmc_host *mmc = host->mmc;
......@@ -922,7 +968,6 @@ static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
{
u8 ctrl;
struct mmc_data *data = cmd->data;
host->data_timeout = 0;
......@@ -1018,25 +1063,7 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
}
}
/*
* Always adjust the DMA selection as some controllers
* (e.g. JMicron) can't do PIO properly when the selection
* is ADMA.
*/
if (host->version >= SDHCI_SPEC_200) {
ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
ctrl &= ~SDHCI_CTRL_DMA_MASK;
if ((host->flags & SDHCI_REQ_USE_DMA) &&
(host->flags & SDHCI_USE_ADMA)) {
if (host->flags & SDHCI_USE_64_BIT_DMA)
ctrl |= SDHCI_CTRL_ADMA64;
else
ctrl |= SDHCI_CTRL_ADMA32;
} else {
ctrl |= SDHCI_CTRL_SDMA;
}
sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
}
sdhci_config_dma(host);
if (!(host->flags & SDHCI_REQ_USE_DMA)) {
int flags;
......@@ -3527,6 +3554,19 @@ static int sdhci_allocate_bounce_buffer(struct sdhci_host *host)
return 0;
}
static inline bool sdhci_can_64bit_dma(struct sdhci_host *host)
{
/*
* According to SD Host Controller spec v4.10, bit[27] added from
* version 4.10 in Capabilities Register is used as 64-bit System
* Address support for V4 mode.
*/
if (host->version >= SDHCI_SPEC_410 && host->v4_mode)
return host->caps & SDHCI_CAN_64BIT_V4;
return host->caps & SDHCI_CAN_64BIT;
}
int sdhci_setup_host(struct sdhci_host *host)
{
struct mmc_host *mmc;
......@@ -3598,7 +3638,7 @@ int sdhci_setup_host(struct sdhci_host *host)
* SDHCI_QUIRK2_BROKEN_64_BIT_DMA must be left to the drivers to
* implement.
*/
if (host->caps & SDHCI_CAN_64BIT)
if (sdhci_can_64bit_dma(host))
host->flags |= SDHCI_USE_64_BIT_DMA;
if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
......@@ -3626,8 +3666,8 @@ int sdhci_setup_host(struct sdhci_host *host)
if (host->flags & SDHCI_USE_64_BIT_DMA) {
host->adma_table_sz = host->adma_table_cnt *
SDHCI_ADMA2_64_DESC_SZ;
host->desc_sz = SDHCI_ADMA2_64_DESC_SZ;
SDHCI_ADMA2_64_DESC_SZ(host);
host->desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
} else {
host->adma_table_sz = host->adma_table_cnt *
SDHCI_ADMA2_32_DESC_SZ;
......@@ -3635,7 +3675,11 @@ int sdhci_setup_host(struct sdhci_host *host)
}
host->align_buffer_sz = SDHCI_MAX_SEGS * SDHCI_ADMA2_ALIGN;
buf = dma_alloc_coherent(mmc_dev(mmc), host->align_buffer_sz +
/*
* Use zalloc to zero the reserved high 32-bits of 128-bit
* descriptors so that they never need to be written.
*/
buf = dma_zalloc_coherent(mmc_dev(mmc), host->align_buffer_sz +
host->adma_table_sz, &dma, GFP_KERNEL);
if (!buf) {
pr_warn("%s: Unable to allocate ADMA buffers - falling back to standard DMA\n",
......
......@@ -185,6 +185,7 @@
#define SDHCI_CTRL_EXEC_TUNING 0x0040
#define SDHCI_CTRL_TUNED_CLK 0x0080
#define SDHCI_CTRL_V4_MODE 0x1000
#define SDHCI_CTRL_64BIT_ADDR 0x2000
#define SDHCI_CTRL_PRESET_VAL_ENABLE 0x8000
#define SDHCI_CAPABILITIES 0x40
......@@ -205,6 +206,7 @@
#define SDHCI_CAN_VDD_330 0x01000000
#define SDHCI_CAN_VDD_300 0x02000000
#define SDHCI_CAN_VDD_180 0x04000000
#define SDHCI_CAN_64BIT_V4 0x08000000
#define SDHCI_CAN_64BIT 0x10000000
#define SDHCI_SUPPORT_SDR50 0x00000001
......@@ -309,8 +311,14 @@ struct sdhci_adma2_32_desc {
*/
#define SDHCI_ADMA2_DESC_ALIGN 8
/* ADMA2 64-bit DMA descriptor size */
#define SDHCI_ADMA2_64_DESC_SZ 12
/*
* ADMA2 64-bit DMA descriptor size
* According to SD Host Controller spec v4.10, there are two kinds of
* descriptors for 64-bit addressing mode: 96-bit Descriptor and 128-bit
* Descriptor, if Host Version 4 Enable is set in the Host Control 2
* register, 128-bit Descriptor will be selected.
*/
#define SDHCI_ADMA2_64_DESC_SZ(host) ((host)->v4_mode ? 16 : 12)
/*
* ADMA2 64-bit descriptor. Note 12-byte descriptor can't always be 8-byte
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment