Commit 68d74315 authored by Ioana Ciocoi Radulescu's avatar Ioana Ciocoi Radulescu Committed by David S. Miller
Browse files

dpaa2-eth: Fix ndo_stop routine



In the current implementation, on interface down we disabled NAPI and
then manually drained any remaining ingress frames. This could lead
to a situation when, under heavy traffic, the data availability
notification for some of the channels would not get rearmed correctly.

Change the implementation such that we let all remaining ingress frames
be processed as usual and only disable NAPI once the hardware queues
are empty.

We also add a wait on the Tx side, to allow hardware time to process
all in-flight Tx frames before issueing the disable command.

Signed-off-by: default avatarIoana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 5191673b
......@@ -1243,34 +1243,36 @@ enable_err:
return err;
}
/* The DPIO store must be empty when we call this,
* at the end of every NAPI cycle.
*/
static u32 drain_channel(struct dpaa2_eth_channel *ch)
/* Total number of in-flight frames on ingress queues */
static u32 ingress_fq_count(struct dpaa2_eth_priv *priv)
{
u32 drained = 0, total = 0;
struct dpaa2_eth_fq *fq;
u32 fcnt = 0, bcnt = 0, total = 0;
int i, err;
do {
pull_channel(ch);
drained = consume_frames(ch, NULL);
total += drained;
} while (drained);
for (i = 0; i < priv->num_fqs; i++) {
fq = &priv->fq[i];
err = dpaa2_io_query_fq_count(NULL, fq->fqid, &fcnt, &bcnt);
if (err) {
netdev_warn(priv->net_dev, "query_fq_count failed");
break;
}
total += fcnt;
}
return total;
}
static u32 drain_ingress_frames(struct dpaa2_eth_priv *priv)
static void wait_for_fq_empty(struct dpaa2_eth_priv *priv)
{
struct dpaa2_eth_channel *ch;
int i;
u32 drained = 0;
for (i = 0; i < priv->num_channels; i++) {
ch = priv->channel[i];
drained += drain_channel(ch);
}
int retries = 10;
u32 pending;
return drained;
do {
pending = ingress_fq_count(priv);
if (pending)
msleep(100);
} while (pending && --retries);
}
static int dpaa2_eth_stop(struct net_device *net_dev)
......@@ -1278,14 +1280,22 @@ static int dpaa2_eth_stop(struct net_device *net_dev)
struct dpaa2_eth_priv *priv = netdev_priv(net_dev);
int dpni_enabled = 0;
int retries = 10;
u32 drained;
netif_tx_stop_all_queues(net_dev);
netif_carrier_off(net_dev);
/* Loop while dpni_disable() attempts to drain the egress FQs
* and confirm them back to us.
/* On dpni_disable(), the MC firmware will:
* - stop MAC Rx and wait for all Rx frames to be enqueued to software
* - cut off WRIOP dequeues from egress FQs and wait until transmission
* of all in flight Tx frames is finished (and corresponding Tx conf
* frames are enqueued back to software)
*
* Before calling dpni_disable(), we wait for all Tx frames to arrive
* on WRIOP. After it finishes, wait until all remaining frames on Rx
* and Tx conf queues are consumed on NAPI poll.
*/
msleep(500);
do {
dpni_disable(priv->mc_io, 0, priv->mc_token);
dpni_is_enabled(priv->mc_io, 0, priv->mc_token, &dpni_enabled);
......@@ -1300,19 +1310,9 @@ static int dpaa2_eth_stop(struct net_device *net_dev)
*/
}
/* Wait for NAPI to complete on every core and disable it.
* In particular, this will also prevent NAPI from being rescheduled if
* a new CDAN is serviced, effectively discarding the CDAN. We therefore
* don't even need to disarm the channels, except perhaps for the case
* of a huge coalescing value.
*/
wait_for_fq_empty(priv);
disable_ch_napi(priv);
/* Manually drain the Rx and TxConf queues */
drained = drain_ingress_frames(priv);
if (drained)
netdev_dbg(net_dev, "Drained %d frames.\n", drained);
/* Empty the buffer pool */
drain_pool(priv);
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment