Commit dd2956ea authored by Yufeng Mo's avatar Yufeng Mo Committed by David S. Miller
Browse files

net: hns3: not allow SSU loopback while execute ethtool -t dev

The current loopback mode is to add 0x1F to the SMAC address
as the DMAC address and enable the promiscuous mode.
However, if the VF address is the same as the DMAC address,
the loopback test fails.

Loopback can be enabled in three places: SSU, MAC, and serdes.
By default, SSU loopback is enabled, so if the SMAC and the DMAC
are the same, the packets are looped back in the SSU. If SSU loopback
is disabled, packets can reach MAC even if SMAC is the same as DMAC.

Therefore, this patch disables the SSU loopback before the loopback
test. In this way, the SMAC and DMAC can be the same, and the
promiscuous mode does not need to be enabled. And this is not
valid in version 0x20.

This patch also uses a macro to replace 0x1F.

Fixes: c39c4d98

 ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: default avatarYufeng Mo <moyufeng@huawei.com>
Reviewed-by: default avatarPeng Li <lipeng321@huawei.com>
Signed-off-by: default avatarHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 2336f19d
......@@ -97,7 +97,7 @@ static int hns3_lp_setup(struct net_device *ndev, enum hnae3_loop loop, bool en)
break;
}
if (ret)
if (ret || h->pdev->revision >= 0x21)
return ret;
if (en) {
......@@ -144,7 +144,10 @@ static int hns3_lp_down(struct net_device *ndev, enum hnae3_loop loop_mode)
static void hns3_lp_setup_skb(struct sk_buff *skb)
{
#define HNS3_NIC_LB_DST_MAC_ADDR 0x1f
struct net_device *ndev = skb->dev;
struct hnae3_handle *handle;
unsigned char *packet;
struct ethhdr *ethh;
unsigned int i;
......@@ -160,7 +163,9 @@ static void hns3_lp_setup_skb(struct sk_buff *skb)
* before the packet reaches mac or serdes, which will defect
* the purpose of mac or serdes selftest.
*/
ethh->h_dest[5] += 0x1f;
handle = hns3_get_handle(ndev);
if (handle->pdev->revision == 0x20)
ethh->h_dest[5] += HNS3_NIC_LB_DST_MAC_ADDR;
eth_zero_addr(ethh->h_source);
ethh->h_proto = htons(ETH_P_ARP);
skb_reset_mac_header(skb);
......
......@@ -223,6 +223,9 @@ enum hclge_opcode_type {
HCLGE_OPC_MAC_ETHTYPE_ADD = 0x1010,
HCLGE_OPC_MAC_ETHTYPE_REMOVE = 0x1011,
/* MAC VLAN commands */
HCLGE_OPC_MAC_VLAN_SWITCH_PARAM = 0x1033,
/* VLAN commands */
HCLGE_OPC_VLAN_FILTER_CTRL = 0x1100,
HCLGE_OPC_VLAN_FILTER_PF_CFG = 0x1101,
......@@ -771,6 +774,31 @@ struct hclge_vlan_filter_vf_cfg_cmd {
u8 vf_bitmap[16];
};
#define HCLGE_SWITCH_ANTI_SPOOF_B 0U
#define HCLGE_SWITCH_ALW_LPBK_B 1U
#define HCLGE_SWITCH_ALW_LCL_LPBK_B 2U
#define HCLGE_SWITCH_ALW_DST_OVRD_B 3U
#define HCLGE_SWITCH_NO_MASK 0x0
#define HCLGE_SWITCH_ANTI_SPOOF_MASK 0xFE
#define HCLGE_SWITCH_ALW_LPBK_MASK 0xFD
#define HCLGE_SWITCH_ALW_LCL_LPBK_MASK 0xFB
#define HCLGE_SWITCH_LW_DST_OVRD_MASK 0xF7
struct hclge_mac_vlan_switch_cmd {
u8 roce_sel;
u8 rsv1[3];
__le32 func_id;
u8 switch_param;
u8 rsv2[3];
u8 param_mask;
u8 rsv3[11];
};
enum hclge_mac_vlan_cfg_sel {
HCLGE_MAC_VLAN_NIC_SEL = 0,
HCLGE_MAC_VLAN_ROCE_SEL,
};
#define HCLGE_ACCEPT_TAG1_B 0
#define HCLGE_ACCEPT_UNTAG1_B 1
#define HCLGE_PORT_INS_TAG1_EN_B 2
......
......@@ -6211,6 +6211,30 @@ static void hclge_cfg_mac_mode(struct hclge_dev *hdev, bool enable)
"mac enable fail, ret =%d.\n", ret);
}
static int hclge_config_switch_param(struct hclge_dev *hdev, int vfid,
u8 switch_param, u8 param_mask)
{
struct hclge_mac_vlan_switch_cmd *req;
struct hclge_desc desc;
u32 func_id;
int ret;
func_id = hclge_get_port_number(HOST_PORT, 0, vfid, 0);
req = (struct hclge_mac_vlan_switch_cmd *)desc.data;
hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_MAC_VLAN_SWITCH_PARAM,
false);
req->roce_sel = HCLGE_MAC_VLAN_NIC_SEL;
req->func_id = cpu_to_le32(func_id);
req->switch_param = switch_param;
req->param_mask = param_mask;
ret = hclge_cmd_send(&hdev->hw, &desc, 1);
if (ret)
dev_err(&hdev->pdev->dev,
"set mac vlan switch parameter fail, ret = %d\n", ret);
return ret;
}
static void hclge_phy_link_status_wait(struct hclge_dev *hdev,
int link_ret)
{
......@@ -6465,6 +6489,20 @@ static int hclge_set_loopback(struct hnae3_handle *handle,
struct hclge_dev *hdev = vport->back;
int i, ret;
/* Loopback can be enabled in three places: SSU, MAC, and serdes. By
* default, SSU loopback is enabled, so if the SMAC and the DMAC are
* the same, the packets are looped back in the SSU. If SSU loopback
* is disabled, packets can reach MAC even if SMAC is the same as DMAC.
*/
if (hdev->pdev->revision >= 0x21) {
u8 switch_param = en ? 0 : BIT(HCLGE_SWITCH_ALW_LPBK_B);
ret = hclge_config_switch_param(hdev, PF_VPORT_ID, switch_param,
HCLGE_SWITCH_ALW_LPBK_MASK);
if (ret)
return ret;
}
switch (loop_mode) {
case HNAE3_LOOP_APP:
ret = hclge_set_app_loopback(hdev, en);
......
......@@ -148,6 +148,8 @@ enum HLCGE_PORT_TYPE {
NETWORK_PORT
};
#define PF_VPORT_ID 0
#define HCLGE_PF_ID_S 0
#define HCLGE_PF_ID_M GENMASK(2, 0)
#define HCLGE_VF_ID_S 3
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment