Commit f68e355c authored by Pekon Gupta's avatar Pekon Gupta Committed by Tony Lindgren
Browse files

ARM: dts: am43xx: add support for parallel NAND flash



This patch:
 - enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
 - adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
   present on following boards:

   am43x-epos-evm:
	On this board, NAND Flash control lines are muxed with QSPI, Thus only
        one of the two can be used at a time. Selection is controlled by:
        (a) dynamically driving following GPIO pin from software
            GPMC_A0(GPIO) == 0 NAND is selected (default)
            GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: default avatarPekon Gupta <pekon@ti.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent c06c5270
......@@ -701,6 +701,30 @@
<&edma 11>;
dma-names = "tx", "rx";
};
elm: elm@48080000 {
compatible = "ti,am3352-elm";
reg = <0x48080000 0x2000>;
interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "elm";
clocks = <&l4ls_gclk>;
clock-names = "fck";
status = "disabled";
};
gpmc: gpmc@50000000 {
compatible = "ti,am3352-gpmc";
ti,hwmods = "gpmc";
clocks = <&l3s_gclk>;
clock-names = "fck";
reg = <0x50000000 0x2000>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
gpmc,num-cs = <7>;
gpmc,num-waitpins = <2>;
#address-cells = <2>;
#size-cells = <1>;
status = "disabled";
};
};
};
......
......@@ -79,6 +79,27 @@
0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */
>;
};
nand_flash_x8: nand_flash_x8 {
pinctrl-single,pins = <
0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.SELQSPIorNAND/GPIO */
0x0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */
0x4 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */
0x8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */
0xc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */
0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */
0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */
0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */
0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */
0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */
0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpmc_wpn */
0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */
0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */
0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */
0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */
0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */
>;
};
};
matrix_keypad: matrix_keypad@0 {
......@@ -184,3 +205,89 @@
&gpio3 {
status = "okay";
};
&elm {
status = "okay";
};
&gpmc {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&nand_flash_x8>;
ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
nand@0,0 {
reg = <0 0 0>; /* CS0, offset 0 */
ti,nand-ecc-opt = "bch8";
ti,elm-id = <&elm>;
nand-bus-width = <8>;
gpmc,device-width = <1>;
gpmc,sync-clk-ps = <0>;
gpmc,cs-on-ns = <0>;
gpmc,cs-rd-off-ns = <40>; /* tCEA + tCHZ + 1 */
gpmc,cs-wr-off-ns = <40>;
gpmc,adv-on-ns = <0>; /* cs-on-ns */
gpmc,adv-rd-off-ns = <25>; /* min( tALH + tALS + 1) */
gpmc,adv-wr-off-ns = <25>; /* min( tALH + tALS + 1) */
gpmc,we-on-ns = <0>; /* cs-on-ns */
gpmc,we-off-ns = <20>; /* we-on-time + tWP + 2 */
gpmc,oe-on-ns = <3>; /* cs-on-ns + tRR + 2 */
gpmc,oe-off-ns = <30>; /* oe-on-ns + tRP + 2 */
gpmc,access-ns = <30>; /* tCEA + 4*/
gpmc,rd-cycle-ns = <40>;
gpmc,wr-cycle-ns = <40>;
gpmc,wait-on-read = "true";
gpmc,wait-on-write = "true";
gpmc,bus-turnaround-ns = <0>;
gpmc,cycle2cycle-delay-ns = <0>;
gpmc,clk-activation-ns = <0>;
gpmc,wait-monitoring-ns = <0>;
gpmc,wr-access-ns = <40>;
gpmc,wr-data-mux-bus-ns = <0>;
/* MTD partition table */
/* All SPL-* partitions are sized to minimal length
* which can be independently programmable. For
* NAND flash this is equal to size of erase-block */
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "NAND.SPL";
reg = <0x00000000 0x00040000>;
};
partition@1 {
label = "NAND.SPL.backup1";
reg = <0x00040000 0x00040000>;
};
partition@2 {
label = "NAND.SPL.backup2";
reg = <0x00080000 0x00040000>;
};
partition@3 {
label = "NAND.SPL.backup3";
reg = <0x000C0000 0x00040000>;
};
partition@4 {
label = "NAND.u-boot-spl-os";
reg = <0x00100000 0x00080000>;
};
partition@5 {
label = "NAND.u-boot";
reg = <0x00180000 0x00100000>;
};
partition@6 {
label = "NAND.u-boot-env";
reg = <0x00280000 0x00040000>;
};
partition@7 {
label = "NAND.u-boot-env.backup1";
reg = <0x002C0000 0x00040000>;
};
partition@8 {
label = "NAND.kernel";
reg = <0x00300000 0x00700000>;
};
partition@9 {
label = "NAND.file-system";
reg = <0x00800000 0x1F600000>;
};
};
};
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment