spi-controller.yaml 3.95 KB
Newer Older
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/spi/spi-controller.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: SPI Controller Generic Binding

maintainers:
  - Mark Brown <broonie@kernel.org>

description: |
  SPI busses can be described with a node for the SPI controller device
  and a set of child nodes for each SPI slave on the bus. The system SPI
  controller may be described for use in SPI master mode or in SPI slave mode,
  but not for both at the same time.

properties:
  $nodename:
    pattern: "^spi(@.*|-[0-9a-f])*$"

  "#address-cells":
    const: 1

  "#size-cells":
    const: 0

  cs-gpios:
    description: |
      GPIOs used as chip selects.
      If that property is used, the number of chip selects will be
      increased automatically with max(cs-gpios, hardware chip selects).

34
      So if, for example, the controller has 4 CS lines, and the
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
      cs-gpios looks like this
        cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>;

      Then it should be configured so that num_chipselect = 4, with
      the following mapping
        cs0 : &gpio1 0 0
        cs1 : native
        cs2 : &gpio1 1 0
        cs3 : &gpio1 2 0

  num-cs:
    $ref: /schemas/types.yaml#/definitions/uint32
    description:
      Total number of chip selects.

  spi-slave:
    $ref: /schemas/types.yaml#/definitions/flag
    description:
      The SPI controller acts as a slave, instead of a master.

patternProperties:
  "^slave$":
    type: object

    properties:
      compatible:
        description:
          Compatible of the SPI device.

    required:
      - compatible

  "^.*@[0-9a-f]+$":
    type: object

    properties:
      compatible:
        description:
          Compatible of the SPI device.

      reg:
        minimum: 0
        maximum: 256
        description:
          Chip select used by the device.

      spi-3wire:
        $ref: /schemas/types.yaml#/definitions/flag
        description:
          The device requires 3-wire mode.

      spi-cpha:
        $ref: /schemas/types.yaml#/definitions/flag
        description:
          The device requires shifted clock phase (CPHA) mode.

      spi-cpol:
        $ref: /schemas/types.yaml#/definitions/flag
        description:
          The device requires inverse clock polarity (CPOL) mode.

      spi-cs-high:
        $ref: /schemas/types.yaml#/definitions/flag
        description:
          The device requires the chip select active high.

      spi-lsb-first:
        $ref: /schemas/types.yaml#/definitions/flag
        description:
          The device requires the LSB first mode.

      spi-max-frequency:
        $ref: /schemas/types.yaml#/definitions/uint32
        description:
          Maximum SPI clocking speed of the device in Hz.

      spi-rx-bus-width:
        allOf:
          - $ref: /schemas/types.yaml#/definitions/uint32
          - enum: [ 1, 2, 4 ]
          - default: 1
        description:
          Bus width to the SPI bus used for MISO.

      spi-rx-delay-us:
        description:
          Delay, in microseconds, after a read transfer.

      spi-tx-bus-width:
        allOf:
          - $ref: /schemas/types.yaml#/definitions/uint32
          - enum: [ 1, 2, 4 ]
          - default: 1
        description:
          Bus width to the SPI bus used for MOSI.

      spi-tx-delay-us:
        description:
          Delay, in microseconds, after a write transfer.

    required:
      - compatible
      - reg

examples:
  - |
    spi@f00 {
        #address-cells = <1>;
        #size-cells = <0>;
        compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
        reg = <0xf00 0x20>;
        interrupts = <2 13 0 2 14 0>;
        interrupt-parent = <&mpc5200_pic>;

        ethernet-switch@0 {
            compatible = "micrel,ks8995m";
            spi-max-frequency = <1000000>;
            reg = <0>;
        };

        codec@1 {
            compatible = "ti,tlv320aic26";
            spi-max-frequency = <100000>;
            reg = <1>;
        };
    };