Commit c86dc03e authored by Wenyou Yang's avatar Wenyou Yang Committed by Mark Brown
Browse files

regulator: act8865: support output voltage by VSET2[] bits



For the step-down DC/DC regulators, the output voltage is
selectable by setting VSEL pin that when VSEL is low, output
voltage is programmed by VSET1[] bits, and when VSEL is high,
output voltage is programmed by VSET2[] bits.

The DT property "active-semi,vsel-high" is used to specify
the VSEL pin at high on the board.

Signed-off-by: default avatarWenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: default avatarLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown's avatarMark Brown <broonie@kernel.org>
parent 6ff33f39
......@@ -261,6 +261,16 @@ static const struct regulator_desc act8865_regulators[] = {
ACT88xx_REG("LDO_REG4", ACT8865, LDO4, VSET, "inl67"),
};
static const struct regulator_desc act8865_alt_regulators[] = {
ACT88xx_REG("DCDC_REG1", ACT8865, DCDC1, VSET2, "vp1"),
ACT88xx_REG("DCDC_REG2", ACT8865, DCDC2, VSET2, "vp2"),
ACT88xx_REG("DCDC_REG3", ACT8865, DCDC3, VSET2, "vp3"),
ACT88xx_REG("LDO_REG1", ACT8865, LDO1, VSET, "inl45"),
ACT88xx_REG("LDO_REG2", ACT8865, LDO2, VSET, "inl45"),
ACT88xx_REG("LDO_REG3", ACT8865, LDO3, VSET, "inl67"),
ACT88xx_REG("LDO_REG4", ACT8865, LDO4, VSET, "inl67"),
};
#ifdef CONFIG_OF
static const struct of_device_id act8865_dt_ids[] = {
{ .compatible = "active-semi,act8600", .data = (void *)ACT8600 },
......@@ -413,6 +423,7 @@ static int act8865_pmic_probe(struct i2c_client *client,
struct act8865 *act8865;
unsigned long type;
int off_reg, off_mask;
int voltage_select = 0;
pdata = dev_get_platdata(dev);
......@@ -424,6 +435,10 @@ static int act8865_pmic_probe(struct i2c_client *client,
return -ENODEV;
type = (unsigned long) id->data;
voltage_select = !!of_get_property(dev->of_node,
"active-semi,vsel-high",
NULL);
} else {
type = i2c_id->driver_data;
}
......@@ -442,8 +457,13 @@ static int act8865_pmic_probe(struct i2c_client *client,
off_mask = ACT8846_OFF_SYSMASK;
break;
case ACT8865:
regulators = act8865_regulators;
num_regulators = ARRAY_SIZE(act8865_regulators);
if (voltage_select) {
regulators = act8865_alt_regulators;
num_regulators = ARRAY_SIZE(act8865_alt_regulators);
} else {
regulators = act8865_regulators;
num_regulators = ARRAY_SIZE(act8865_regulators);
}
off_reg = ACT8865_SYS_CTRL;
off_mask = ACT8865_MSTROFF;
break;
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment